Thursday, June 8, 2017

Confessions of an Automationeer, Part 13: The Myth of the Straight-Six Supercar

Confessions of an Automationeer, Part 13: The Myth of the Straight-Six Supercar


As described my the previous post, the straight-six engine is making a comeback in the real-life automotive industry after decades of being overshadowed - and replaced - by more compact and supposedly cheaper-to-develop V6 engines. Having described the benefits of inline sixes compared to equivalent V6s, I set myself a challenge involving the use of such an engine, but it wouldn't be for a mass-market volume model. Instead, I would attempt to prove that a supercar or hypercar powered by a straight-six engine could be a competitive offering.



The SMG Hissho: Rolling proof that inline sixes still belong in the engine bays of supercars and hypercars... contrary to popular belief.

To complicate matters even more, I had decided to prioritize light weight and high efficiency over outright performance for this build. Fortunately, the body I chose had excellent aerodynamics, which helped greatly during the engineering phase. The design phase was quite simple, though; I ended up building a car with relatively clean, uncluttered styling in which the side intakes were placed next to the rear window, rather than on the car's flanks. Eventually, I called my car the SMG Hissho LS; Hissho is Japanese for "certain victory" and LS is short for "Lightweight Spec".


500 horses, plenty of torque and not too thirsty for a turbo six... what's not to like about this engine?

The Hissho's turbocharged straight-six had a magnesium block and ran 1.25 bar of boost on premium unleaded. Careful tuning yielded a fairly flat, wide torque curve and 500 horsepower at 7600 rpm, with a redline of 8000 rpm. And with its undersquare dimensions, the engine still weighed less than 200 kilograms even with the turbo hardware included. Having finalized the engine specs, I was now ready to focus on the rest of the car.

In keeping with my aim of making a light car, the body, chassis and wheels were made out of carbon-fiber, while the interior was relatively pared back and covered in lightweight materials. To harness the engine's considerable torque output, the Hissho had an electronically controlled differential, rear spoiler, and dampers. These advanced technologies, combined with the low curb weight of 1.3 metric tons, ensured that the Hissho's dynamics were excellent, with minimal body roll. Moreover, it achieved 30 mpg (US) on the combined cycle - an unusually high figure for a supercar) thanks to careful selection of gear ratios and spacing. And yet, against all odds, at its pre-markup price, it achieved a competitiveness score of over 100 in the two regions in which it could be sold.

Immediately, however, I began wondering how good the Hissho was. As it turned out, I had already built many similar designs to the Hissho over the past few months; this one, though, didn't rely too heavily on quality sliders, as some of those builds did. Even so, I secretly believed that, for a car like this, 500 horsepower wouldn't always be enough. For this reason, shortly before I began work on this economy-oriented build, I decided to take the idea to its logical conclusion. The result was surprising, to say the least.



A concept build of a more extreme six-cylinder hypercar, with ~700 horsepower.


Unlike the Hissho, this earlier build was created with the aim of determining how much power could be squeezed from a straight-six engine given the small engine bay in the body I had chosen. It seemed easier said than done, given the fact that a straight-six is much longer than an equivalent V6, but eventually, I managed to extract a whopping 700 horsepower from a highly undersquare 3.5-liter straight-six. The resulting engine is shown below.


700 bhp from a 3.5L turbo I6? Incredible!

By most objective performance standards the Hissho would have been no match for the bright orange wedge I had made, although the extra torque (and the additional turbo lag that comes with it) made it far less drivable. Nevertheless, it seems fair to consider this test build as a great car in its own right. This is especially apparent when one takes into account the fact that the trim shown here was derived from a less powerful version, aimed at the lower end of the market, but I chose not to show it here because I felt that the Hissho was more deserving of a place on this blog.

That concludes my discussion of straight-six-powered, mid-engined supercar builds, but I won't be done with this engine configuration for some time yet. In the next post, I will explain my plans for the UE4 release of Automation, which is already in open beta.

Sunday, June 4, 2017

Confessions of an Automationeer, Part 12: The Joy of Six

Confessions of an Automationeer, Part 12: The Joy of Six


For eight of the past ten CSR rounds I have entered, my entries were powered by a straight-six engine. Now you may be wondering whether or not I am biased towards this particular engine configuration. In truth, I certainly am not, but have done my homework about the pros and cons of the various engine configurations available in Automation. So, without further ado, here's an example of a (turbocharged) straight-six done right, provided by another user who was willing to share his secrets.


The turbo setup for the winning entry in CSR41

Look at the dyno sheet in the screenshot above and you'll see that the torque curve is very smooth, wide and flat, with minimal lag. For this to occur, small-diameter compressors and turbines have to be used in conjunction with a high AR ratio and low boost pressure. The latter, especially when combined with a high compression ratio, allows for further improvements in efficiency; moreover, the use of a lean air-fuel ratio and conservative ignition timing make this engine even more economical.

On top of that, the low-RPM cam profile is very mild, while the high-RPM cam profile is fairly aggressive. However, due to budget constraints, this engine has a simple air-to-air intercooler and a standard three-way catalytic converter. Installing a water-to-air intercooler (which lowers the engine's minimum required octane number, thereby allowing the compression ratio to be increased even more) would cause efficiency to increase further, while a less restrictive high-flow converter would have a similar effect. So it's not hard to see why four of the eight straight-sixes I made during the past CSR were turbocharged.

But even without turbochargers, straight-sixes are preferable to V6s for several reasons. Whereas a V6 has its cylinders arranged in two banks of three, a straight-six has its cylinders arranged in a straight line. The former needs a bank angle of 120 degrees - too wide for most engine bays - to be inherently balanced, and as such, most V6 engines have either a 90-degree bank angle (which leads to less refinement and more complication, even if the resulting engine was derived from a V8) or a 60-degree bank angle (smoother, but more expensive to develop).  Moreover, a straight-six suffers from reduced friction losses compared with an equivalent V6, and also requires fewer components. Finally, it will be easier and cheaper to develop a straight-three or straight-four from a straight-six if they all share the same internal dimensions. The only advantage a V6 has over a straight-six with the same dimensions is its reduced length, and as such, it only makes sense to use one if the engine bay is particularly small.

In short, when budgets are relatively modest and efficiency is key, but a modicum of performance is desired, the sweet spot among engine configurations doesn't always lie with eight cylinders or more, or, for that matter, five or fewer. It can be found in the humble straight-six, and this once-commonplace arrangement looks set to make a comeback. In the next post, I will show a recent build in an attempt to prove that even a supercar (or hypercar, for that matter) can use this relatively humble configuration and still remain competitive in the cutthroat Automation market.

Monday, May 29, 2017

Confessions of an Automationeer, Part 11: War Wagons

Confessions of an Automationeer, Part 11: War Wagons

After two straight rounds of building what were essentially street-legal track cars (especially appropriate given the context of those rounds), CSR changed tack again. This time, users were given the enviable task of building fast, sporty, yet practical daily drivers - with wagons (estate cars to those of you in Europe and elsewhere) being the preferred body style. As such, while I wasn't required to build one, I did so anyway. And once again, I decided to take full advantage of the engineering time and cost limits - now more generous than previously - by throwing in the kitchen sink when designing my entry.


Does this tick all the boxes for an enthusiast with a growing family... It sure looks like it does...

For the fourth straight round I opted for a straight-six engine up front (it isn't among my favorite engine configurations for nothing), driving the rear wheels, and as was the case during CSR39, it was normally aspirated, with an alloy block. Yet again I chose a fully independent suspension on both axles, and set it up to oversteer, just so that I could give the driver a sportier feel from behind the wheel. Again, all the fundamentals for a great driver's car were present - manual gearbox, limited-slip diff, high-performance tires, etc.

So far, so good. But as soon as one particular entrant revealed and submitted his entry, there was absolutely no chance of anyone else winning the round outright. But why? A quick look at its dyno sheet revealed the answer.


How's this for consistency?

Looking at the menu for the turbo setup, it's clear that what turned out to be the winning car had a turbocharged straight-six with a small-diameter compressor and turbine, plus a small amount of boost and a lean air/fuel ratio. This provided an extremely high level of efficiency, especially for 1995, the year in which this round was set. More importantly, with a fat, flat torque curve throughout the rev range, in-gear acceleration would have been incredibly rapid. One can only wonder how much more potent and economical it would be if it were modernized with direct fuel injection...


Get used to that rear view - you'll have little time to appreciate it...

So, to hardly anyone's surprise, the Dragotec Helios took a comfortable victory in CSR41. It was economical, fun to drive and shot through with quality. On top of that, it was still affordable, both in the short and long term. However, I could once again finish the round with my head held high, as I usually do - my entry attracted glowing praise for its sporty dynamics, especially considering that it was purely rear-wheel-drive. At the time this post was published, the theme for the next round has yet to be announced - I will be curious to find out.

Sunday, May 28, 2017

Confessions of an Automationeer, Part 10: Back on Track

Confessions of an Automationeer, Part 10: Back on Track


You may be wondering why I named this post "Back on Track". The reason is twofold. I originally planned to begin writing on Tuesday, but a suicide bombing in Manchester, combined with a few other well-known people passing away within the same 24-hour period, made me reconsider. So I gave myself some time to grieve, and it would be several days before I could muster the mental strength to continue.

On a more positive note, this post earned its name because, for two rounds in a row, CSR - the crown jewel of competitions on the official Automation forums - had a racing/track day theme. CSR39 was about building a relatively affordable, reliable car capable of dominating a track day at Circuit Zolder in Belgium; CSR40, on the other hand, was a challenge to supply a race team with a fast, reliable turbocharged touring car. Naturally, I jumped straight into both rounds. In fact, given that I started work on this post on the same day that the Monaco Grand Prix and Indianapolis 500 were held, the topic of this post is particularly fitting, as is its name.

My CSR39 entry, the 2000 Zorg ZS36, was quite straightforward - a front-engined, rear-drive coupe with double wishbones at each corner and powered by a 3-liter normally-aspirated straight-six. I set it up to oversteer, but not to the point that it felt unacceptably wayward. As befitting the track-day theme for CSR39, it came with a sports interior, a six-speed manual gearbox hooked up to a mechanical LSD, and vented disc brakes front and rear. And on top of that, it was finished in bright yellow, making it utterly unmissable.


Zorg ZS36 Coupe

When the time came to judge the entries the ZS36 was clearly a car to consider. The host's only complaint was that it oversteered slightly more than was preferable, but otherwise it was a strong contender. In the end, though, the win went instead to another yellow coupe - the Smooth Pretaco R. In hindsight, it was hard to see anything else winning the round; its light weight, combined with its free-revving engine, made it nigh-on unbeatable around the track.


Smooth Pretaco R

In the very next round, entrants were tasked with building a touring car powered by a turbocharged engine with a displacement of up to 2500 cc, preferably with 4 or 6 cylinders. Once again I made yet another rear-drive coupe - the 1985 SMG Taikan A-Spec. Finished in white and adorned with a prominent rear wing, its turbocharged all-alloy straight-six developed around 300 bhp, which I reckoned would be enough to make it competitive.


SMG Taikan A-Spec

Once again, it was difficult to determine the finalists, let alone the winner. Even so, anything with ineligible (or overly complicated) parts, or was too slow, unreliable, uncomfortable, undrivable and/or expensive would be rejected out of hand. My entry wasn't among the many cars to suffer this fate, though. However, it was ultimately eliminated later on due to concerns about engine reliability, presumably because it had an all-alloy engine. In the end, another coupe from Smooth took the win; this time, it was the blood-red, wedge-shaped, whale-tailed Duster SR, whose combination of simplicity, affordability, endurance, and outright pace was unmatched.


Smooth Duster SR

As this post is being written, CSR41 has just concluded, and ideas for CSR42 are being discussed. Thus, it would make sense for me to discuss either or both rounds in my next post. Meanwhile, with the UE4 version of Automation in open beta, I will soon have to decide whether or not to test it before it is publicly released...

Saturday, May 20, 2017

Confessions of an Automationeer, Part 9: The Search for a Ute

Confessions of an Automationeer, Part 9: The Search for a Ute


CSR38 was another one of my favorite rounds in the history of the competition, but for an entirely different reason compared with the previous one, which had the dark, gritty and adrenaline-pumping feel of a late-80s action film such as Die Hard. Instead, it was much more humorous and lighthearted, and on top of that was set in the present day instead of being a period piece. Most significantly of all, though, entrants were tasked with building examples of a kind of car that most people outside Australia and New Zealand are largely unaware of: the ute. Basically, a ute is similar in design to a pickup truck, but is based on the body and chassis of a passenger car. And given that I had seen plenty of utes (especially V8-powered ones) during both of my visits to Australia, entering this round was a no-brainer for me.

At the time this post was published, the ute body style was just a few months away from being consigned to the history books, with the possible (but unlikely) exception of one-off bespoke coachbuilt special based on existing two-door coupes. With this in mind, the client for this round requested a ute that was not only practical, but reasonably fast in a straight line and yet cheap to buy and run, thus keeping the genre alive for ute-lovers everywhere. On top of that, there was a possibility that the ute's value would increase over time if it were prestigious enough - the car's age would also be factored into this calculation. And so, having read the requirements, I set about building my entry.


A ute that thinks it's a sports coupe: the Zorg ZV4 Utility

After a few hours of deliberation, I settled on a car-based ute with all-independent suspension at each corner (sacrificing load capacity for improved dynamics), and powered by a small-displacement (2.6 liters) turbocharged straight-six optimized mainly for economy and running on regular (91RON) unleaded. The resulting car was called the Zorg ZV4 Utility and, in this trim at least, was offered in a bright metallic blue. To keep the occupants happy on long trips, I made a premium interior and infotainment system standard, with an advanced safety suite and a full set of driving aids thrown in for good measure. And yet it was merely the base model for the entire model line I had in mind, with more powerful engines being optional across the range - but I won'd get too far ahead of myself; a detailed description of the ZV4 will have to wait until later.

As the other entrants submitted their entries I was awestruck by the sheer number of approaches to the client's request, and gradually became increasingly confused as to which one of them would win the round - arguably more so than the round host, in fact. While I was building a show pony that could tackle even the twistiest roads with aplomb, some users built straight-line stoplight warriors capable of showing a clean pair of tailpipes to most sports cars (but weren't usually quite as good at everything else); others built honest, no-nonsense cargo haulers so far removed from the definition of ute that they were, to all intents and purposes, trucks - which, sadly, have largely replaced the ute as the vehicle of choice for Australian tradesmen. There were even several wildcard entries using older bodies (including a few cars which were essentially restomods - older models fitted with modern mechanicals), if only for the "retro factor" the client requested from the dozens of entrants. Specifically, a car which used an older body, or was introduced in an earlier year, would be deemed more desirable due to the client's preference for classics, although in order to pull that off, the rest of the car would have to be a true standout in many other areas as well.

Among the entries were a few utes sent in merely to make up the numbers and were built by users who knew full well that they would not make it past the first cut. But this eclectic mix of not-quite-trucks also contained a few all-purpose utes that, on first impressions at least, were good all-around choices. And although I hadn't entered to win, I was still keyed up with anticipation as the results were announced, as I had always been. Clearly the contest needed a change of tone after the dark, moody feel of the previous round.

When the results finally arrived I immediately burst into laughter after seeing the first set of reviews, which proved to be blunt yet very lighthearted, even for CSR. Even as I found out that my ute was not quite practical enough to make the first cut, I did not care one bit because the host had elevated the standards of writing and story development (for this contest, at least) to a hitherto unseen level. Considering that the previous round had already set the bar very high in this regard, that's saying something. And still the reviews kept coming, each one being more hilarious and honest than the last. After this, the list of semifinalists was finalized; it consisted entirely of vehicles which were not only practical enough for consideration, but were quite fun to drive, as well as being easy on the wallet and eye.

Thus, after the first round of cuts, there were only a dozen utes still being considered: the El-Enterato, the Daemon TK, the Dragotec Coyote, the Maverick Loadstar, the Cario Clone, the Factory Lorry, the Starfire SE-8, the Ridgeback Express, the BandicUte (either a portmanteau of Bandit and Cute, or Bandicoot and Ute - either one is correct), the Reveho GX-Z, the Quebec Utility S, and the FOA Outlander. Of these, only six of them would be finalists. The rest would, sadly, be eliminated at this stage, even though they were not without merit, unlike some of the less successful entrants. It is worth noting that had some other users been able to finalize their entries, they would have entered this round as well, which would have made at least the first round of cuts even tougher still.

In this next round of cuts, any remaining utes that lacked the necessary utility value to be viable were cut, as were entries that were too expensive. In particular, the Reveho was cut simply because it was a truck with two rows of seats - definitely contradictory with the traditional definition of a ute. Likewise, the Starfire SE-8 was overpriced, while the Quebec Utility S and Cario Clone were too middle-of-the-road to make it to the final cut. Finally, the BandicUte was just too small. Every other semifinalist was still being considered, however.






Top to bottom: CSR38 semifinalists - Reveho, Cario Clone, Quebec Utility S, BandicUte and Starfire SE-8

And so to the final decision, which proved to be the toughest one of all. First to go was the El-Enterato, which was simply outclassed by its remaining rivals. The Outlander, meanwhile, had tires that were far too narrow for a ute, much less a quasi-off-roader, and the Daemon TK was just too old to be an economical choice in the client's view. Most disappointingly of all, the Maverick Loadstar was not safe enough, and the Coyote's lack of traction control made it an unacceptably difficult everyday proposition.







Top to bottom: CSR38 finalists - El-Enterato, Daemon TK, Outlander, Coyote and Ridgeback

This left the client with just two utes to choose from: the Ridgeback and Factory Lorry. Deciding upon a winner turned out to be extremely difficult, but in the end the Factory Lorry got the nod, mostly on account of being a more honest and useful workhorse overall, even though it was much less of a show pony (i.e. fun to drive) even than the Ridgeback. Even so, with a few changes, it would have been highly likely that victory would have gone to the Ridgeback instead. And so, after a round spent building a kind of car that will soon be consigned to the history books in real life, CSR changed tack - and shifted its focus to track cars.

Thursday, May 4, 2017

Confessions of an Automationeer, Part 8: CSR37 Retrospective

Confessions of an Automationeer, Part 8: CSR37 Retrospective

There have been thirty-eight Car Shopping Rounds held on the Automation forums since the contest began in January 2016, but the thirty-seventh one, set in 1987, is my clear favorite for several reasons. First, the host gave entrants a fairly liberal rule set to work with, even though there were quite a few key guidelines to follow, leading to unprecedented diversity in the ways it could be interpreted. Secondly, a comprehensive story was provided, ensuring that entrants would be immersed in it until the very end. Finally, when the results were announced, the buildup and epilogue drew plenty of inspiration from action movies of the late 80s.

So to give some explanation for the context of this round, I'll start by mentioning the backstory. Some time in 1987, an enigmatic client requested a car from a brand with sporting provenance... as long as it costs less than $20,000 with a 30% markup in place. He also wanted a radio and a tape deck, while the engine and car had to be developed fairly quickly and at a reasonable cost. And on top of that, it had to look good - including the paint job.

Despite the restrictions I was forced to work with, the rule set was still liberal enough to allow a wide variety of interpretations on the users' behalf. In my case, it led to the creation of a traditional front-engined, rear-drive, normally-aspirated, V8-powered muscle car: the NMI (National Motor Industries) Arrowhead 5.7. I opted for such a design philosophy because I wanted to have some cash to spare and keep the reliability levels high. In fact, the Arrowhead was heavily inspired by the era's American muscle cars (Camaro, Corvette, Mustang, etc.) but had an independent rear end to give it the handling prowess enthusiasts normally associate with premium European imports. However, the use of a normally aspirated engine would have ramifications later on, not all of them positive, although I didn't know it when I submitted the design.


My entry for CSR37: the NMI Arrowhead 5.7

As the days went by, the host received a flood of entries, and I could not help but be awestruck by the sheer variety of the field. Considering that the round was set in a period where performance cars had undergone a renaissance, the entry list was quickly populated by everything from supercars to rally homologation specials and virtually everything in between. In fact, I was wondering if my submission was among the more conservative entries, not just mechanically but also visually.

After a week-long period in which entries were submitted, the host began to announce the final results. As expected, the first cars to be cut were either poorly designed or simply did not perform well enough - or both. Naturally, this eliminated many promising contenders, but my Arrowhead wasn't among them - yet. The quality of the remaining contenders clearly made the next round of cuts much more difficult.

Next to fall were the normally aspirated cars - although in fairness, nobody who submitted them, myself included, saw this coming. Considering that the client only wanted turbocharged cars in the end, however, this was clearly justified. This left just seven cars to battle it out for victory. Deciding a winner, however, turned out to be even tougher than compiling the shortlist of potential contenders.

Once again, any cars that didn't meet the client's exacting standards would be cut. Inevitably, this led to yet more contenders being eliminated, leaving just three cars: the Butzi BiTurbo, Salmon GT-Sprint, and Miglia Turbo. Either of the former two could have won, but did not; as fast as they were, the Miglia turned out to be even sportier - and better-looking to boot. So the car that looked and felt most like a supercar ended up taking a well-deserved victory.




Top to bottom: Butzi BiTurbo, Salmon GT-Sprint and Miglia Turbo


What made this the most exciting round of CSR up to that point (at least in my opinion), though, was the epilogue, in which the client was attacked by several heavily armed mobsters and attempted to escape from them in the Miglia. While reading it, I was reminded of contemporary action films and TV series such as Die Hard, Miami Vice and the like. In fact, considering that the prologue revealed very little about the client except for the fact that he wanted a relatively affordable performance car, I was convinced that this would be a round with a darker tone than usual, and events proved me right.

To put the epilogue in a nutshell, shortly after they arrived, the mobsters stole many of the cars that had been evaluated by the client; realizing the gravity of the situation, he soon picked up his loyal sidekick and shot out one of his pursuers' front tires, causing a massive pileup and triggering a huge explosion. The only mobsters to avoid the crash were the ones in the red Sagata 3.8 Turbo - a car which, despite its impressive performance, failed to make the first cut; they soon opened fire on him again, forcing him to return fire while relying on the Miglia's performance (and his supreme driving skills) to stay one step ahead of his pursuers. But while the local police also took off after the mobster and his prey, they were no match for the firepower of the former or the driving skills of the latter. Eventually, after a brief but intense chase through the city, he shot out both of the Sagata's front tires, sending it sliding out of control into a petrol station and exploding on impact. This time, the mobsters did not survive.




The victor and the vanquished: the Sagata 3.8 Turbo (top) and Merlo Turbo (bottom)

Thus ended the closest thing that CSR has ever had (or will ever have, considering the lighter tone of most other rounds) to an action film. It should be noted that a few months before CSR37, there had been a similar performance-oriented contest (which, unlike CSR37, revolved around building ultra-high-end supercars for a movie director to use in an upcoming film), but it was a one-off set in the present day and was much more liberal, with a far higher budget limit. I did better in that challenge, though, only missing out on a spot in the top three because of my car's styling, which was... unusual to say the least, although I heavily revised it in a second trim I created afterwards. And now, having read the epilogues of both contests, I am starting to see striking similarities between them. Next up is a post about the quest to buy an example of a kind of (virtual) car you may not be aware of.

Friday, April 21, 2017

Automation Earth Day Special: Designing an Engine for Efficiency

Automation Earth Day Special: Designing an Engine for Efficiency

In celebration of Earth Day, I have chosen to create a new post specifically with environmental awareness in mind. For this I have chosen to show an example of an engine configured for high fuel efficiency and low emissions. In particular, I will share how I achieved both of those objectives. But before that, I will go into why I built the car which is powered by that engine.

A few weeks ago, I found a contest on the Automation forums that required entrants to build an economy car for a buyer whose previous car had been destroyed in a crash. Given my expertise in optimizing an engine for high efficiency, entering this challenge (which would easily have been a round of CSR if not for its creator not having won the most recent round) was a no-brainer. So, after a few hours, I came up with this:



The Zorg ZV2 1.7 AWD: Designed for economy at a reasonable price

My entry, the Zorg ZV2 1.7 AWD, looked like a normal, if small, three-box sedan from the outside, but with all-wheel-drive, fully independent suspension at each corner and alloy panels on a high-strength steel chassis, it was a technically advanced offering. It was also practical and affordable enough to be a sensible daily driver. However, the real genius lay under the hood.






Top to bottom: Internals and variant capacity, cam profiles and compression, turbocharger setup, fuel system configuration, and technical overview of the 1.7-liter straight four in the Zorg ZV2 1.7

In an attempt to extract as much efficiency from the engine as possible given the limited budget, I settled on low-friction pistons (which provide a significant increase in efficiency), a shorter stroke (to prevent the redline from restricting power outputs too much), mild cam profiles (which ensures that the valves are open for a shorter time) and a lean air/fuel ratio (again, providing sizable economy gains). The most significant work, however, was tuning the turbocharger for increased fuel economy. For this application, small compressors and turbines with modest boost and a low AR ratio were a necessity, and I did not hesitate to apply my expertise here.

The end result was an efficiency rating of 32% - an impressive figure given the tight budget. As installed in the ZV2, it provided excellent fuel economy figures (although in a lighter car, it would have yielded even better results) - high-40s to low-50s US MPG on the combined cycle - and very low emissions. Speaking of which, hypereutectic pistons actually reduce emissions even further than low-friction pistons, but aren't as useful in economy-oriented applications due to their increased friction, although they are strong enough to withstand higher redlines. For the next post, I will kick off my series of CSR retrospectives... by stepping back 30 years.